 |
DESCRIPTION:
RTG (Rubber Tyred Gantry) Crane.
WLL:
130 ton.
PROJECTNR.:
LT847
.
|
 |
DESCRIPTION:
Main shaft fixture 2.3MW Siemens. Designed for changing the gearbox without dismounting the rotor. Ejector system pushes gear box off main shaft. Part of Liftra's broad range of fixtures for main shafts.
PROJECTNR.:
LT586
APPROVED FOR:
European Union (EU), USA, Canada.
.
|
 |
DESCRIPTION:
Main shaft fixture and rotor lock for GE 1.5MW Siemens. Designed for changing a gearbox without dismounting the rotor. Part of Liftra's broad range of fixtures for main shafts.
PROJECTNR.:
LT560
.
|
 |
DESCRIPTION:
Wagon to move main shafts or other components that are placed in a trestle. The trestles are adjustable for different diameters.
WLL:
10 ton.
PROJECTNR.:
LT552
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Fixture for main shaft. Designed for changing a gearbox without dismounting the rotor.
Fits NEG MICON NM1500-1650 and NM64-82 and VESTAS V82. Part of Liftra's broad range of fixtures for main shafts.
WLL:
93 ton.
PROJECTNR.:
LT019-2
APPROVED FOR:
USA.
.
|
 |
DESCRIPTION:
LT Carrier Gantry. Moves any component that can be lifted in one point. Can reach over a flatbed truck, to load and unload. Drives both in parallel mode in any direction - or in normal mode where the carrier turns around a line through the center of the carrier. Battery driven which makes the noise emission extremely low, and allows the carrier to drive inside the factory.
WLL:
90 ton.
PROJECTNR.:
LT494
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Adjustment yoke for drive train. A lifting yoke for lifting and adjusting drive train for wind turbine.
WLL:
77 ton.
PROJECTNR.:
LT481
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Transport frame for 6M nacelle.
WLL:
365 ton.
PROJECTNR.:
LT471
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
LT Carrier Gantry. Moves any component that can be lifted in 1 point. Can reach over a flatbed truck, to load and unload. Drives both in parallel mode in any direction - or in normal mode where the carrier turns around a line through the center of the carrier. Battery driven which makes the noise emission extremely low, and allows the carrier to drive inside the factory.
WLL:
80 ton.
PROJECTNR.:
LT194
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Bridge yoke. A bridge yoke that is designed for continuous rotation of a load.
WLL:
91 ton.
PROJECTNR.:
LT409
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Turning yoke. A turning yoke that is able to turn a load 180º.
WLL:
85 ton.
PROJECTNR.:
LT401
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Fixture for change of gearbox on MM. Fixture for use in nacelle during replacement of gearbox.
WLL:
175 ton.
PROJECTNR.:
LT393
APPROVED FOR:
European Union (EU), USA.
.
|
 |
DESCRIPTION:
LT Fork Carrier. The carrier is battery driven, which gives a very low noise emission. The traction and lift is hydraulic driven and has servo steering.
WLL:
10 ton.
PROJECTNR.:
LT276
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Vacuum yoke. Designed to lift and move glass-fiber section for wind turbine nacelle sections of different shapes and sizes. The yoke is flexible and can be turned and angled in many directions.
WLL:
360 kg/1 ton.
PROJECTNR.:
LT233
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Internal Crane for NM2000 . A small crane used to lift a gear cover plate so the high speed shaft can be changed in the turbine.
The crane is constructed to be assembled inside the wind turbine.
WLL:
2.2 ton.
PROJECTNR.:
LT227
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Trolley. Designed for use with Samag carrier. The trolley is used for various loads of maximum 10 ton.
WLL:
10 ton.
PROJECTNR.:
LT216
APPROVED FOR:
European Union (EU).
.
|
 |
DESCRIPTION:
Lifting yoke for transmission NM1500-NM2750.
WLL:
50 ton.
PROJECTNR.:
LT011
APPROVED FOR:
European Union (EU).
.
|
